V3 FOLDING TRANSPORT WAGON - BLENDER DEVELOPMENT MODEL
Revision A / English edition / 2026-11-03

OPEN FIRST
V3_Folding_Wagon_120kg_RevA_EN.blend: deployed source model.
V3_Folding_Wagon_Storage_RevA_EN.blend: the same model in flat-storage pose.
Created in Blender 4.5.15 LTS. All materials are procedural; no external textures.
One Blender unit is one metre; the interface displays millimetres.

RENDERS
V3_Deployed_Front_EN.png: assembled front three-quarter view, 2048x1720.
V3_Deployed_Rear_EN.png: assembled rear three-quarter view, 2048x1720.
V3_Flat_Storage_EN.png: flat-storage view, 2048x1450.
V3_Corner_Lock_and_Hinge_EN.png: corner lock / offset-hinge detail, 2048x1720.
V3_Folded_Underside_EN.png: underside showing four retained horizontal wheels,
2048x1450. The ground is hidden for this inspection view.
These are actual Blender Cycles renders from the included mesh model.

OTHER FILES
V3_Deployed_EN.glb / V3_Flat_Storage_EN.glb: portable static PBR mesh previews.
The blend sources retain the control drivers and fine procedural materials.
build_v3_blender_EN.py: complete, self-contained rebuild source, also embedded.
V3_Model_Parameters_EN.json: layout proposals and measured mesh envelopes.
V3_Model_Validation_EN.json: geometry and control checks after saved-file reload.
V3_Reference_Concept_EN.png: English concept board used as a visual reference.

LAYOUT AND DIMENSIONS
Cargo transport payload target: 120 kg, unverified.
Body target excluding the raised handle: 900 x 580 x 520 mm.
Handle top: approximately 1100 mm when fully extended, 900 mm when retracted.
Reference folded target: 900 x 580 x 230 mm.
Evaluated final storage mesh: approximately 900 x 580 x 227.5 mm.
The small difference between a mesh envelope and a target is not a production
tolerance or allowance. Mass and usable cargo volume have not been calculated.

Complete rigid deck and continuous load frame; no central deck-fold hinge.
Four independent rigid green panels with ivory top strips. The corner uprights
are attached to the long panels and fold with them. Short panels fold first;
the long panels fold above them. All panels remain attached for daily storage.
Two front caster modules and two rear fixed modules fold inward as complete
retained carriers, leaving four approximately horizontal wheels under the deck.
Wheel diameter 250 mm, tyre width 65 mm, proposed track 475 mm.

DEVELOPMENT ADJUSTMENTS FROM THE EARLIER CONCEPT NOTES
The new model uses short-panel hinge axes 14 mm above the deck and long-panel
hinge axes 40 mm above it. The earlier idealised sketch used 36 mm for the long
hinges; the extra 4 mm accommodates visible corner uprights and lock receivers.
The proposed panel hinge spacing is 780 mm longitudinally and 498 mm laterally.
Carrier fold axes are 231 mm above the deployed ground; retained fork and axle
heads are included in the measured overall envelope. These are new spatial
layout proposals; earlier concept dimensions were not frozen manufacturing CAD.

POSES AND EDITING
Select V3_MASTER_CONTROLS, then Object Properties > Custom Properties.
front_short_panel_deg / rear_short_panel_deg: 0 upright, 90 inward.
near_long_panel_deg / far_long_panel_deg: 0 upright, 90 inward.
wheel_carriers_fold_deg: 0 deployed, 90 inward beneath the deck.
handle_extension_mm: 0 retracted, 200 extended.
handle_fold_deg: 0 upright, -25 parked outside, 90 stowed above panels.
handle_pin_withdraw_mm: 0 engaged, 36 withdrawn clear of the handle foot.
socket_cover_deg: 0 closed, 95 demonstration open pose.
handle_lift_mm: lift the complete handle/hinge/foot after withdrawing the pin.
deck_tipping_deg: separate tipping-cradle pose, 0-35 degrees for development.

For convenient complete pose changes, open Blender's Text Editor and select
one of the embedded POSE_*.py texts, then Run Script:
POSE_OPEN, POSE_HANDLE_PARKED, POSE_SHORT_PANELS_DOWN, POSE_ALL_PANELS_DOWN,
POSE_HANDLE_STOWED, POSE_FLAT_STORAGE.
These presets set geometry controls only; they do not simulate a person,
interlocks, latch internals, mass, contact physics or a validated folding motion.
The flat-storage file places the master root below Z0 so the folded wheels
rest on the studio ground. The OPEN preset restores root Z0 before deployment.
When adjusting controls manually from storage, reset root Z0 as needed.

FOLDING INTENT - EMPTY WAGON ONLY
1. Retract the handle and park it outside the panel sweep.
2. Release four corner locks. Fold front and rear short panels inward.
3. Fold the near and far long panels with their corner uprights.
4. Stow the retracted handle above the panels and retain it in storage clips.
5. Support the empty wagon, separately release the carrier locks, fold all
four wheel modules beneath the deck and retain them for storage.
Panel-service hinge pins and complete handle removal are separate actions.

MODEL SCOPE
This editable Blender mesh is for appearance, layout and mechanism discussion.
Production solid CAD, mould-ready PP walls/ribs, load analysis, actual latches,
carrier stops, springs, return actions, caster sweeps, brakes, fastener selection,
fits, tolerances, mass and pinch protection still require engineering work.
Final-pose envelope/layer-gap checks do not establish full-motion clearance.
The 120 kg development target has not been demonstrated by calculations or tests.
Permitted tipping load must be established separately from transport payload.

REBUILD
blender --background --factory-startup --python build_v3_blender_EN.py -- --final
Use --preview for two lower-resolution open/storage images and both blend files.
The script saves its outputs beside itself. Preview/final rebuilds overwrite
those output files; make a copy before retaining a custom-edited source model.
