EN LIGHT - REV B ENGINEERING HANDOFF - ENGLISH EDITION
Design revision: 2026-11-02 | English issue: 2026-11-03

PURPOSE AND REVISION CONTROL
Factory-feedback revision: raised lid, single-colour enamel and leg frames that flip up as the carry handle.
The user confirmed the dual-use leg arrangement on 2026-11-02. There is no separate bucket-style carry bail.
This edition translates the Chinese Rev B package. The design geometry and nominal parameters are unchanged.
Use the drawings, model and parameters in this English folder together. Rev A is historical reference.

1. DESIGN CHANGES ALREADY INCLUDED
1.1 Bowl: OD330, nominal depth 80. Lid: OD332; rise increased from 32 to 85.
    Closed height with deployed frames is about 240, compared with 235 including the old fixed handle.
    Nominal lid headroom above the food grate: 89.3 at the centre and 60.3 at radius 140.
    A D280 x H50 cylindrical food-space example has about 10.3 minimum vertical space above it.
    These values exclude enamel, thermal deformation, fit tolerances and food-shape variation.
    This example is not a rated food size or cooking capacity. All dimensions are millimetres.
1.2 Bowl and lid use the same white enamel on both inner and outer surfaces; approve the factory colour sample.
    Stainless hardware, grates and heat-rated foot/grip sleeves are outside the single-colour enamel scope.
1.3 The fixed lid-top handle and large separate carry bail are removed.
    Two D6 U-frames deploy as legs and flip upwards to meet as the carrying grip.
    Pivot axis: X direction, Z112. Front half-span: 170; rear half-span: 178.
    Coaxial short-pin stack is provisional. There is no long shaft through the firebox.
    Deployed rail centres: Y +/-148, Z7.
    At about 122.2 degrees up, central grip sleeves lie at Y +/-10, Z293.2.
    Raised grip centre spacing: 20. Each sleeve: OD14 x L80. Underside-to-lid-crown gap: about 46.2.
    Compact stow angle: about 11.3 degrees. Stowed envelope: about 372 x 346 x 209.
    The raised-frame view is suspended carrying, not a resting configuration.
    About 300 is the frame-top height relative to deployed Z0, not the suspended assembly's own height.
1.4 The lower ash cup supplies intake air; the lid vent is the exhaust.
    Grates, ash cup and local heat reflector retain their previous nominal arrangement.
1.5 With no fixed lid-top handle, provide a purchased rim-clamp lid lifter and test its grip, temperature and rim compatibility.
    The vent is not a handle for lifting the lid.

2. FACTORY ENGINEERING STILL REQUIRED
2.1 Rigid deployed stops and independent anti-fold locks on both U-frames. Pivot friction alone is insufficient.
2.2 Stowed/carry position retention; a coupling to hold the two grips together; an operating sequence that prevents pinching or accidental release.
    Model lock blocks only identify required locations. Support the cold body while moving each frame.
    Validate whether one person can safely perform the complete operation on a sample.
    Cool completely, remove ash and latch the lid before flipping the legs for carrying.
    Restore deployed support and lock both frames before resting the grill on a table.
2.3 Inner reinforcement at side mounts, welding before enamelling, short coaxial pin stack, fits, anti-loosening and transport lid clips.
2.4 Deep-lid draw radii, draft and springback; rolled-rim fit; enamel allowance; grate and food clearance.
2.5 Ash-cup removal path; all fastener, vent and lock interferences; thermal distortion, tipping, temperature rise and durability.
    Frames are longer and the lid is taller. Unchanged product weight is not claimed; calculate part and assembled masses.

3. COMPLETED CHECKS AND THEIR LIMITS
The native file has been reopened. Four pose envelopes, three closed-shell meshes and uniform enamel have been checked.
At 61 angles from 0 to 122.2 degrees, frame tubes, central sleeves and foot pads were checked against the main bowl/lid surfaces; no surface intersections were found.
This sample check excludes a complete assembly check, continuous minimum clearance, locks, coating/thermal expansion, tolerances, loads, centre of gravity and temperature.
The DXF contains ten editable views in millimetre modelspace. Geometry, arrows and text are separate entities, not associative parametric dimensions.
Blender is editable mesh/curve visualization. It is not STEP, parametric mechanical CAD or approved tooling geometry.
English localization preserves the native mesh/curve geometry and four pose transforms; the stored signature comparison matches.

4. TOOLING AND COST
The supplier's approximate RMB 40,000 figure is an initial estimate from the chat, not a confirmed quotation.
First obtain existing bowl/deep-lid mould diameters, inner sections, depths, rim fit, usable sheet gauges and available hole/mount positions.
Discuss reuse only if food clearance and assembly fit can be maintained. A matching factory mould has not been established.
Clarify new-tool, reuse, alteration and trial charges, taxes, freight, lead time and price differences.

5. FILE INDEX
01_Engineering_Drawings: five A3 landscape sheets as PDF and PNG; print at 100% actual size.
02_CAD_and_Parameters: millimetre DXF, unified nominal parameters, lid-clearance data and coordinate guide.
03_Blender_Model: native BLEND, closed-pose static GLB, four actual Cycles renders, build/check scripts and verification.
04_Design_Overview: English support/carry comparison board.
05_Factory_Feedback: clearly labelled English transcription of the supplied chat and factory response form.
90_Package_Tools: English document and package generation scripts.

The original Chinese chat image is preserved in the earlier Chinese source package, outside this English deliverable.
This folder and ZIP do not contain approved production CAD, STEP, mould design or a mass-production release.
